steel@pandapipe.com

Pipe size Chart – NPS,ND,OD,Wall Thickness

Table of Contents

What Is Pipe Size?

We all know that pipe size are composed of the pipe’s outer size, inner size, and wall thickness. But do you know what pipe size means? While the first thing you think of when you think of pipe diameter is the outer size of the pipe, it often refers to the nominal size, a point that can be confusing.

Pipe size

Why Is Pipe Size So Important?

Pipe size is the nominal diameter of a pipe, often referred to as NPS. This is a standardized size identifier, representing a size code rather than the actual physical size. However, thanks to the pipe diameter, pipe fittings from different manufacturers can be matched. NPS is used to determine the size when ordering, avoiding ordering errors caused by differences in communication and understanding.

Pipe Size Development History

The IPS system was used in the 19th century. With the development of industry, the American Society of Pipe Sizing (ASA) introduced the NPS system in 1927. This separated the dimensions from the actual physical dimensions and published a standard system for pipe wall thickness (Schedule). Subsequently, Europe invented the DN system, which, along with the NPS, has become the global standard for pipe sizes today.

Why are Pipe Size and OD Easily Confused?

Now that we know that pipe diameters and OD are easily confused, do you know which part of the pipe is the pipe diameter and which part is the OD?

NPS1⁄8 to 12

At this stage of the pipeline, NPS is close to OD. As shown in the figure below

NPS 14 And Above

In this size pipe, NPS is the actual OD

Pipe Diameter

Pipe Size Chart

NPS: Nominal Pipe Size , based on the metric system, approximates the inside diameter in inches. It applies to North America and some Commonwealth countries.

DN: Diameter Nominal , based on the imperial system, is merely a designation in millimeters. It applies to Europe, China, and countries that adhere to ISO standards.

How to Specify Pipe Diameter in an RFQ

A pipe diameter inquiry should use at least one clear size system: NPS or inch, DN, or the actual outside diameter in millimeters. Do not provide only a number such as “4-inch pipe” without confirming whether it refers to the nominal pipe size or the measured outside diameter.

For an accurate quotation, PANDAPIPE recommends specifying:

  • Pipe size: NPS, DN or actual OD in mm
  • Wall thickness or schedule
  • Material grade and standard
  • Pipe length and quantity

Example: ASTM A53 Grade B, NPS 4, SCH 40, 6 m length, 500 pieces.

Based on our quotation experience, unclear diameter descriptions are a common reason for specification confirmation delays. Providing both the nominal size and actual OD—for example, NPS 4 / DN 100 / OD 114.3 mm—helps the supplier verify the requirement quickly.

How to Choose the Pipe Size Correctly

1. First, determine the fluid’s properties (density, viscosity, corrosiveness, state, etc.) and calculate the required flow rate, as this directly affects the inner diameter. Determine the flow rate: approximately 10-30 m/s for gases/steam, 0.5-2 m/s for slurries/solid-laden fluids, and 1-3 m/s for liquids such as water and oil.

2. Use the following formula to roughly calculate the inner diameter of the pipe

d: Pipe inner diameter (mm)
Q: Flow rate (L/min)
v: Flow velocity (m/s)

3. After calculating the minimum inner diameter, determine the wall thickness of the pipe you need. If you calculate the minimum inner diameter to be 15mm and you want a pipe with a wall thickness of SCH40, you can consult the table above and use OD minus SCH40 wall thickness to get the inner diameter. Find the NPS that matches your calculated inner diameter. Note that the inner diameter value of OD minus wall thickness must be larger than the calculated inner diameter because we calculated the minimum inner diameter. You can then determine that the pipe diameter you need is NPS 1/2.

If you are not sure about the pipe size you need, you can click below to contact a PANDAPIPE expert. PANDAPIPE is a pipe company that integrates production and application, and is a company you can trust.

Can PANDAPIPE Supply Non-Standard Outside Diameters?

Non-standard outside diameters are commonly requested for equipment components, mechanical structural parts, pipe piles, cofferdams and excavation-support projects. In these applications, the pipe may not need to connect with standard fittings, so the required OD is often determined by the equipment or structural design.

When a buyer asks for the “maximum” or “minimum” pipe diameter, the actual concern is usually whether the manufacturer can produce and supply that size—not simply the theoretical range shown in a pipe chart. Production feasibility depends on the manufacturing process, wall thickness, steel grade, order quantity and dimensional tolerance.

For a non-standard OD inquiry, provide the actual OD, wall thickness, length, quantity, application and applicable tolerance. PANDAPIPE can then check the available production route and material supply before confirming the quotation.

Manufacturer’s Note: Wall-thickness tolerance does not change the ordered pipe length when the purchase is based on fixed lengths or pieces. However, it can affect the actual unit weight. For orders purchased by a fixed total tonnage, a higher actual weight per meter may result in fewer total meters.

Related Products

Our Advantages

  1. Over 25 years of experience in pipeline production and installation.
  2. Comprehensive inspection equipment.
  3. Independent product serial numbers for traceability.
  4. Advanced production equipment – Seamer high-frequency welding machine from the United States.
  5. Complete qualifications – API 5L/API 5CT/FM/UL fire pipe certification, etc.
  6. Wide range of products – independently developed solar torque tubes, highly favored in the European market.
  7. Customers spread across the globe.
  8. Excellent after-sales service and sense of responsibility.
en_USEnglish

CONTACT US